Gas and electric on-demand units sized, permitted, and installed by licensed pros

Tankless water heater installation Annapolis MD that ends cold showers

When your tank gives out or your family keeps fighting over hot water, tankless water heater installation Annapolis MD gives you endless hot water in a fraction of the footprint. We size the unit to your fixtures, pull the Anne Arundel County Plumbing Permit, and handle gas line or electrical upgrades. One visit, code-correct work, and a system warrantied for years.

↗
Fast online booking

Request service today

Tell us what is happening. Our local team will confirm your visit shortly.

No spam. No obligation. Just practical help.
Thanks — we'll call shortly to confirm your visit.
Experienced Plumber Annapolis MD md professionals at work
Careful work. Honest options.
About this service

What tankless water heater installation Annapolis MD involves

Tankless water heater installation Annapolis MD is the licensed process of replacing a storage-tank water heater with an on-demand unit that heats water only when a fixture calls for it. The job covers load calculation, gas line sizing or dedicated electrical circuits, mounting, venting, condensate management on high-efficiency models, and final code inspection. We install Rheem, Navien, and Bradford White units, and we run copper pipe or PEX tubing depending on your home's layout.

Most Annapolis homeowners call us for one of three reasons: a tank leaking onto the garage floor, a household of four running out of hot water by 7 a.m., or a renovation that added a second bathroom. Older homes near the Historic District often have undersized gas lines that need upgrading before a gas tankless water heater installation Annapolis MD can pass inspection. We check all of that before quoting.

  • ✓ Endless hot water
  • ✓ Lower standby losses
  • ✓ Reclaim closet space
  • ✓ Longer service life
What's included

What our tankless installation includes

Every tankless job we run includes the essentials below. If your home needs a gas line upgrade, a new electrical circuit, or a vent relocation, we quote that separately before work starts so the final bill matches the estimate.

✓

Unit sizing and model selection

We calculate peak demand in gallons per minute and match it to a Rheem, Navien, or Bradford White model. You get the sizing sheet and the model number in writing before you commit.

✓

Permit and inspection

We pull the Anne Arundel County Plumbing Permit, schedule the inspection, and meet the inspector on site. The signed permit card stays with your home records.

✓

Old unit removal and haul-away

We drain the old tank, disconnect gas and water, and haul it out. Floors are protected during the swap, and we clean the utility area before we leave.

✓

Venting and condensate handling

High-efficiency units need proper venting and a condensate line. We install both to manufacturer clearances and Maryland code, with neutralizer where required.

✓

Pressure test and walkthrough

Every joint is pressure-tested and every fixture is run hot before we pack up. We show you the temperature setting, the flush ports, and the warranty registration.

How it works

How our tankless installation process works

01

Phone assessment

We ask about your current unit, fuel type, fixture count, and where the heater sits. That 10-minute call tells us whether you need a gas or electric unit and whether your gas line or panel can handle it. We schedule the on-site visit within 24 to 48 hours.

02

On-site sizing

A licensed tech measures incoming gas pressure, checks venting routes, and calculates peak hot-water demand in gallons per minute. We inspect the electrical panel for electric units and confirm clearances. You get a written quote the same day, with the unit model and any line upgrades spelled out.

03

Permit and prep

We pull the Anne Arundel County Plumbing Permit and schedule the inspection. On install day we protect floors, shut off gas and water, drain the old tank, and haul it away. Most swaps take four to six hours; gas line upgrades add two to three hours.

04

Install and test

We mount the unit, run copper pipe or PEX tubing, install the vent, and wire the controls. Then we pressure-test every joint, check for gas leaks with a detector, and run hot water at every fixture to confirm temperature and flow. You see the numbers before we pack up.

05

Inspection and walkthrough

The county inspector signs off on the permit, usually within two business days. We walk you through the temperature setting, the flush procedure, and the warranty registration. You get the manual, the permit card, and our number for anything that comes up later.

Tools & methods

Tools and methods we use on tankless installs

Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.

Press tool

We use a press tool for copper pipe connections where a soldering torch is a fire risk, such as tight utility closets and wood-framed chases. Press fittings are code-approved and faster than solder.

Soldering torch

For exposed copper runs where press fittings are not practical, we solder joints and pressure-test them. Every soldered joint is checked before the wall goes back.

Pipe cutter

Clean, square cuts on copper pipe and PEX tubing prevent leaks at fittings. We cut and deburr every pipe before assembly.

Leak detection camera

Before we close up a wall or chase, we inspect the run with a leak detection camera. It catches drips behind insulation that a pressure test alone can miss.

Manometer

We measure incoming gas pressure at the meter and at the unit. A tankless unit needs adequate pressure to fire reliably, and a manometer tells us if the line needs upgrading.

Multimeter

For electric units, we verify voltage and amperage at the dedicated circuit. This confirms the panel and wiring can carry the load before we mount the unit.

Real results

Before and after.

From leaking tank to wall-hung Navien

Before

A 12-year-old 50-gallon tank in an Eastport garage was leaking from the base. The homeowner was mopping up water daily and had already replaced the drain pan once.

After

We removed the tank, installed a Navien condensing unit on the garage wall, and upgraded the gas line to 3/4-inch. Hot water now reaches the second-floor shower in about 20 seconds, and the floor stays dry.

Third bathroom without a second tank

Before

A family of five in Arnold added a bathroom and found the existing 50-gallon tank could not keep up. Morning showers ran cold by the third person.

After

We sized a gas tankless unit at 9.5 gallons per minute, which covers three showers plus the dishwasher. The family stopped staggering wake-up times, and the gas bill dropped about 22 percent the first full month.

Electric tankless for a basement rental

Before

A Downtown Annapolis rowhouse owner wanted to rent the basement but had no separate hot water. Sharing the main house's tank would have meant unreliable supply and utility disputes.

After

We installed a dedicated electric tankless unit with its own circuit and shutoff. The rental passed inspection, and the owner now has two independent systems with separate metering.

Problems we solve

Problems a tankless install solves

Most of our tankless calls start with a symptom the homeowner is tired of living with. Here are the ones we hear most in Annapolis.

Ask a pro →
01

Running out of hot water during morning routines

We size a gas tankless unit to your fixture count, often 9 to 11 gallons per minute, so simultaneous showers and laundry do not compete. The unit fires only when a tap opens and holds temperature within a degree.

↗
02

Tank leaking or rusting out

We shut off the supply, drain and remove the failed tank, and install a wall-hung tankless unit that holds roughly a gallon of water. No tank means no catastrophic tank failure later.

↗
03

Utility closet too small for a new tank

A tankless unit mounts on a wall and takes about 2 square feet. We check clearances and venting routes during the site visit and often fit the unit where a tank cannot go.

↗
04

High gas bills from standby heat loss

Tankless units heat on demand, so you pay for hot water you actually use. We also check for pipe insulation gaps during install and fix them while we are in the utility area.

↗
Transparent pricing

What tankless installation costs in Annapolis

$1,800 - $5,800 depending on fuel type and line upgrades

Typical 2026 pricing in this area runs $3,200 to $5,800 for a gas tankless install and $1,800 to $3,500 for electric, including permit and haul-away. Gas line upgrades add $600 to $1,500, and electrical panel work adds $800 to $2,000. The cost to install tankless water heater Annapolis Maryland depends mainly on fuel type, line upgrades, and venting route. We quote the full scope before work starts so the final bill matches the estimate.

A tankless unit lasts about 20 years with annual maintenance, roughly double a tank. Spread over that life, the installed cost is often lower per year than replacing a tank twice, and you get endless hot water in the bargain.

01Fuel type

Gas units cost more upfront because of venting and gas line work, but they deliver higher flow rates. Electric units cost less to install but may require a dedicated circuit and panel capacity.

03Electrical panel work

Electric tankless units draw significant amperage. If your panel lacks capacity, adding a dedicated circuit or upgrading the panel adds $800 to $2,000.

04Venting route

A short vertical vent through the roof is simpler than a long horizontal run through a finished wall. Complex routes add labor and materials.

Proof you can check

Licensed, permitted, and reviewed

✓
Maryland Master Plumber LicenseMaryland State Board of Plumbing
✓
Maryland Journeyman Plumber LicenseMaryland State Board of Plumbing
✓
Backflow Prevention CertificationMaryland Department of the Environment
✓
OSHA Safety CertificationOccupational Safety and Health Administration
Customer reviews

What Annapolis customers say

★★★★★
“Our 12-year-old tank started leaking on a Friday. The team came out Saturday morning, quoted a Navien gas unit, and installed it Monday. They pulled the permit and met the inspector. We have not run out of hot water once, even with two teenagers.”
KM

Karen M.Homeowner, Eastport

✓ Verified
★★★★★
“We wanted electric tankless for a basement remodel. They checked our panel, added a dedicated circuit, and installed a Rheem unit. Water is hot in seconds and the app shows usage. The tech walked me through descaling so I can do it myself each spring.”
PS

Priya S.Homeowner, West Annapolis

✓ Verified
Good questions

Tankless water heater questions Annapolis homeowners ask

+1 (831) 293-1204

Yes for most households that plan to stay put five years or more. A gas unit runs $3,200 to $5,800 installed in 2026, and the 20-to-30 percent gas savings plus a 20-year service life usually beats replacing a tank every decade. If you are selling within two years, the payback math is tighter.

Most Annapolis jobs land between $3,200 and $5,800 for a gas unit and $1,800 to $3,500 for electric, including permit and haul-away. Gas line upgrades add $600 to $1,500, and electrical panel work adds $800 to $2,000. The cost to install tankless water heater Annapolis Maryland varies mainly with fuel type and line upgrades.

A straight swap takes four to six hours on install day. Add two to three hours if we are upgrading the gas line, and a full day if the electrical panel needs a dedicated circuit. The county inspection usually happens within two business days after we finish.

They do, with one caveat: Annapolis water runs moderately hard, so annual descaling is not optional. We install isolation valves and flush ports on every job to make that a 30-minute homeowner task. Sized correctly, a gas unit handles a three-bath colonial without temperature swings.

Ready when you are

Get your tankless water heater installation Annapolis MD scheduled

Call us with your address and current setup. We will tell you what fits, what it costs, and when we can install. Same-day estimates available, and every job is permitted and inspected.

Book an estimate +1 (831) 293-1204 →
Request an appointment

Contact Plumber Annapolis MD

Call us at +1 (831) 293-1204 or email [email protected]. We answer the phone 24/7 for emergencies and schedule same-day or next-day visits for non-urgent work. Tell us what's wrong and your address, and we'll give you a time window and a price range before we head out.

Call anytime+1 (831) 293-1204Email the office[email protected]
Office hoursOpen 24 hours · 7 days a week
Request received — our team will be in touch shortly.
Tap to call+1 (831) 293-1204