Licensed, permitted, and warrantied tank and tankless installs across Anne Arundel County.

Water Heater Installation Annapolis MD Done Right the First Time

When your old tank starts leaking or the hot water runs out before your shower does, water heater installation Annapolis MD homeowners trust means a code-correct swap done in a day. We handle the Anne Arundel County Plumbing Permit, haul away the old unit, and pressure-test every connection before we leave. Whether you need a 40-gallon tank or a high-efficiency Navien, we size it to your house and your budget.

↗
Fast online booking

Request service today

Tell us what is happening. Our local team will confirm your visit shortly.

No spam. No obligation. Just practical help.
Thanks — we'll call shortly to confirm your visit.
Water Heater Installation in Annapolis, Maryland
Careful work. Honest options.
About this service

Water Heater Installation Annapolis MD: What the Job Really Involves

Water heater installation Annapolis MD is the licensed removal of your old tank or tankless unit and the code-compliant install of a new one, including the permit, the drain pan, the expansion tank, and the final safety check. It is not a swap-and-go job. We shut off the gas or breaker, drain the old tank, cut out corroded copper pipe or brittle PEX tubing, and rebuild the connections with new pipe fittings and Teflon tape. Then we fill, purge the air, and test the temperature-pressure relief valve before you ever touch the tap.

Most Annapolis homeowners call us for one of three reasons: the tank is 10 to 12 years old and rusting at the seams, the pilot keeps going out, or a family of four keeps running cold. If you are searching for water heater installation near me Annapolis MD because you woke up to a puddle in the garage, we can often get a new unit in the same day. We also handle water heater replacement Annapolis MD for homeowners upgrading to a larger tank or a heat-pump model.

  • ✓ Hot Water That Lasts
  • ✓ Lower Utility Bills
  • ✓ Code-Correct and Permitted
  • ✓ No Surprise Leaks
What's included

What Our Water Heater Installation Includes

Every install we do covers the essentials: the unit, the permit, the haul-away, and the safety check. Here is what is in the standard price and what we handle on site.

✓

New Unit and Connectors

We supply the new tank or tankless unit plus fresh flexible connectors, pipe fittings, and Teflon tape. We do not reuse old shut-off valves or corroded nipples.

✓

Permit and Inspection

We pull the Anne Arundel County Plumbing Permit and meet the inspector on site. You get the signed-off paperwork for your records and your insurance.

✓

Old Unit Haul-Away

The old tank goes on our truck and off your property. No curbside pile, no trip to the dump, no disposal fee tacked on later.

✓

Drain Pan and Relief Valve

We install a new drain pan and test the temperature-pressure relief valve and the expansion tank. These are the parts that prevent a small leak from becoming a flooded floor.

✓

Pressure Test and Walkthrough

We fill the tank, purge the air, and run hot water at every fixture. Then we show you the shut-off, the settings, and the warranty terms before we pack up.

How it works

What to Expect on Install Day

01

Call and Sizing

You call, we ask about the house, the number of bathrooms, and the fuel type. We give you a price range over the phone and book a window, usually same-day or next-day. If you are replacing an emergency failure, tell us and we move you up.

02

On-Site Assessment

The technician checks the old unit, the venting, the gas line or breaker, and the space. We confirm the size and model, show you the price in writing, and get your okay before any work starts. No surprises on the invoice.

03

Removal and Prep

We shut off the water and fuel, drain the old tank with a hose, and disconnect the lines. The old unit goes on the truck for haul-away. We inspect the floor and the shut-off valve and replace anything that will not survive the new install.

04

Install and Test

The new unit goes in level, with a new drain pan, new flexible connectors, and a fresh Teflon-taped fitting set. We solder or press the copper, fill the tank, purge the air, and run the hot water at every fixture until it is clear and hot.

05

Permit and Walkthrough

We schedule the Anne Arundel County inspection, meet the inspector on site, and hand you the warranty paperwork. Before we leave, we show you the shut-off, the relief valve, and the settings so you know how to kill the water in a hurry.

Tools & methods

Tools and Methods We Use on Every Install

Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.

Pipe cutter and soldering torch

Clean cuts and leak-free copper joints. We also carry a press tool for tight spots where a torch is not safe.

Pipe wrench and pipe fittings

Removing old nipples and tightening new connections. We replace every fitting we touch rather than reusing corroded parts.

RIDGID leak detection camera

Tracing a leak to the tank, the pipe, or the slab before we commit to a replacement.

Milwaukee press tool

Crimping PEX tubing and copper press fittings in tight mechanical closets where a torch would be a fire risk.

Drain snake and hydro jetter

Clearing sediment and scale from the lines after a tank swap so hot water reaches every fixture.

Real results

Before and after.

12-Year-Old Tank to New 50-Gallon Rheem

Before

A 12-year-old 40-gallon tank in Eastport was leaking from the bottom seam and leaving rust stains in the drain pan. The family of four was running out of hot water by the second shower.

After

We installed a new 50-gallon Rheem with a fresh drain pan, new connectors, and a permit. Hot water now lasts through four showers, and the leak is gone. The job took three hours.

Tank to Navien Tankless in Parole

Before

A homeowner in Parole wanted endless hot water for a growing family. The old 50-gallon tank took up most of the garage wall and could not keep up with two showers and a dishwasher at once.

After

We installed a Navien tankless unit, upgraded the gas line, and ran new venting. The wall space came back, and the hot water never runs out. The install took seven hours.

Emergency Swap After a Burst Pipe

Before

A frozen pipe burst in a West Annapolis garage and soaked the water heater's electrical connection. The tank was 11 years old and the homeowner had no hot water.

After

We repaired the burst pipe, dried the area, and installed a new 40-gallon unit with a fresh breaker and drain pan. The relief valve and expansion tank were tested. Hot water was back the same day.

Problems we solve

Problems We Solve With a New Water Heater Install

If you are searching for a way to replace old water heater Annapolis Maryland, these are the failure modes we see most often and how a new install fixes them.

Ask a pro →
01

Tank leaking from the bottom seam

We shut off the water, drain the tank, and install a new unit with a fresh drain pan. If the leak reached the subfloor, we flag it so you can dry it out before mold sets in.

↗
02

Hot water runs out in 10 minutes

We flush the old tank to confirm the diagnosis, then size a new unit to your household. A 50 gallon water heater installation Annapolis MD usually solves the problem for a family of four.

↗
03

Pilot light or igniter keeps failing

We test the gas line and venting before we sell you a new heater. If the unit is sound, we repair it. If it is at end of life, we install a new Rheem or Bradford White unit with a fresh vent.

↗
04

Rusty or smelly hot water

We check the anode rod and the tank interior. If corrosion has started, replacement is the only fix. We install a new unit and check your water pressure so the next tank lasts.

↗
Transparent pricing

What Water Heater Installation Costs in Annapolis

$1,200 - $4,500 depending on unit and scope

Typical 2026 pricing in this area runs $1,200 to $2,400 for a standard tank install, including the unit, permit, and haul-away. Tankless and heat-pump models run $2,800 to $4,500 because of venting and electrical upgrades. The price depends on tank size, fuel type, and how much of the old plumbing needs to be rebuilt. We quote the full job before we start, so the number you hear is the number you pay.

A new water heater lasts 10 to 15 years, and a permitted, code-correct install protects your insurance and your resale. The cheapest quote often skips the permit and the drain pan, which is exactly where the problems start.

01Tank size and model

A 40-gallon tank costs less than a 65-gallon or a heat-pump unit. Higher-efficiency models cost more up front but cut monthly bills.

03Venting and code upgrades

Older homes may need a new vent, a power-vent kit, or a chimney liner. These are code requirements, not upsells, and they affect the final price.

04Permit and inspection

Anne Arundel County charges a permit fee, and we include it in the quote. Skipping the permit saves a little now and costs more at resale.

Proof you can check

Licensed, Permitted, and Warrantied

✓
Maryland Master Plumber LicenseMaryland State Board of Plumbing
✓
Maryland Journeyman Plumber LicenseMaryland State Board of Plumbing
✓
Backflow Prevention CertificationMaryland Department of the Environment
✓
OSHA Safety CertificationOccupational Safety and Health Administration
Customer reviews

What Annapolis Customers Say

★★★★★
“Our 12-year-old tank started leaking on a Friday morning. I called and they had a new 50-gallon Rheem in by 2 p.m. The tech pulled the permit, hauled the old unit away, and showed me how to shut the water off. No mess left behind and the price matched the quote.”
KM

Karen M.Homeowner, Eastport

✓ Verified
★★★★★
“We switched to a Navien tankless and the crew handled the venting and gas line upgrade in one day. They walked us through the temperature settings and the annual flush. Hot water never runs out now, even with two teenagers.”
PS

Priya S.Homeowner, Parole

✓ Verified
Good questions

Frequently Asked Questions

+1 (831) 293-1204

Most standard tank installs run $1,200 to $2,400 in 2026, including the unit, permit, and haul-away. Tankless and heat-pump models run higher, often $2,800 to $4,500, because of venting and electrical upgrades. The cost to install water heater in Annapolis Maryland depends on tank size, fuel type, and whether the old unit comes out cleanly.

A standard tank swap takes two to four hours from arrival to hot water. Tankless conversions take longer, usually six to eight hours, because we run new gas lines or electrical. If you book same day water heater installation Annapolis MD, plan on the crew being at your house for most of the afternoon.

A family of two usually needs a 40-gallon tank, three to four people need 50 gallons, and five or more need 65 to 80 gallons. If you have two bathrooms and a dishwasher, lean toward 50 gallons. We check your fixture count and peak-hour use before we recommend a size.

Yes. Anne Arundel County requires a plumbing permit for a water heater replacement, and the work must be inspected. We pull the permit, meet the inspector, and keep the paperwork for you. Skipping the permit can void your homeowner insurance and create a problem when you sell the house.

Ready when you are

Get Your Water Heater Installation Annapolis MD Booked Today

Cold showers do not fix themselves. Call us with your address and the old tank size, and we will give you a price and a window. Licensed, insured, and permitted through Anne Arundel County.

Book My Install +1 (831) 293-1204 →
Request an appointment

Contact Plumber Annapolis MD

Call us at +1 (831) 293-1204 or email [email protected]. We answer the phone 24/7 for emergencies and schedule same-day or next-day visits for non-urgent work. Tell us what's wrong and your address, and we'll give you a time window and a price range before we head out.

Call anytime+1 (831) 293-1204Email the office[email protected]
Office hoursOpen 24 hours · 7 days a week
Request received — our team will be in touch shortly.
Tap to call+1 (831) 293-1204